SOUND OFF

RELOCATED BACKWRAP ROLL
PROVIDES MORE BELT DRIVING FORCE

The backwrap roll is located lower and further forward under the apron drive roll. This increases the surface area contact between the belt and roll, improving driving efficiency and reducing belt slip by 20% in all crops.

THREE BELT CHOICES

Choose standard New Holland MRT (Mini-Rough Top) Clipper laced belts with three plies of poly fabric and top and bottom layer of rubber. Premium laced belts (shown) are manufactured with constant heat and pressure to eliminate belt flaws and improve tensile strength. They feature new low-profile Alligator™ rivet fasteners with DuraLink™ stainless steel flexible pins. For ultimate durability and low maintenance, new endless belts feature a completely spliceless design for maximum consistency and wear resistance. They offer the best balance of durability, low maintenance, sure grip and delicate handling.

STAY INFORMED WITH YOUR
CHOICE OF MONITOR

You monitor and control the bale-making process with the new Bale Command™ II (twine only)/Bale Command™ II Plus (twine and net, twine only, or net only) system (shown). Or, go ISOBUS with the IntelliView™ III color touchscreen monitor (IntelliView™ IV available through parts). Bale fill sensors on the side of the bale chamber use a new, more durable heat-treated arm. Sensor readouts are displayed as bar graphs on the monitor.

TWINE WRAP SYSTEM WITH SIMPLIFIED ADJUSTMENTS

Dual twine tubes move across the bale from the left side of the baler to the right and back again for a controlled, consistent wrap pattern across the bale face. You can change the twine tube spacing and speed to control twine spacing. You can carry up to eight active balls of twine without dividers or six with dividers, up front with up to four additional twine balls on spare carriers one on each side of the baler with two non-active balls per side carrier.

SIMPLIFIED NET WRAPPER: EXCELLENT
VISIBILITY AND EASY LOADING

The net knife and wrapper are now controlled by separate motors, reducing amperage draw on the system. The net knife now moves up to cut the net, pulling the net into the knife for more positive cutting action. The New Holland front-load net wrapping system is highly visible so it’s easy to watch your baling operation running smoothly from the tractor seat. A simple, shorter, more efficient net travel path makes it the industry’s most reliable system, with less chance for misfeeding.

EXCLUSIVE BALE-SLICE™ SYSTEM

For bales that are more dense, easy to feed and easier for livestock to digest, equip your Roll-Belt™ 560 with New Holland’s industryexclusive Bale-Slice™ system. Since knives enter the bale after the core is made, bales retain a solid core, and you decide how much of the bale is cut to the outside bale face. Bales made by the Bale-Slice system are up to 14% denser than unsliced and can increase the average daily weight gain in yearling heifers by 23%* plus higher production rates across the board. Now that’s SMART for the way you raise cattle!

THREE PICKUP CHOICES

THE HEAVY-DUTY, FIVE-BAR ACTIVESWEEP™ PICKUP USES:
NEW Two-piece, solid-steel tinebars with dual tinebar cams
NEW Stronger, rubber-mounted, heavy-duty, six-millimeter steel curved tines—32 double tines
per bar for 160 tines total
NEW Four double-plate reel spiders to carry the tinebars
NEW Larger-diameter in-feed augers
NEW Improved stronger pickup bands
NEW Improved bolt-in dividers that run the full-length of the backbone
NEW Cut out clutch for overload protection on Bale-Slice and Specialty Crop models, as well as
a built-in declutching system on all balers to shut down belts during bale ejection
NEW Castering quick-adjust gauge wheels
Need Optional Castoring quick-adjust gauge wheels
THE STANDARD-DUTY, FOUR-BAR ACTIVESWEEP™ PICKUP USES
NEW Two-piece tinebars pinned in the center with dual tinebar cams
NEW 24% stronger five-millimeter steel coil tines that are curved and shot-peened—32 double
tines per bar for 128 tines total
NEW Optional bolt-in, full-length pickup dividers that run the full length of the backbone
NEW Three plate-type reel spiders carry the tinebars
NEW Castering, quick-adjust gauge wheels
NEW Three double plate reel spiders carr the tine bars
NEW Optional Castoring, quick-adjust gauge wheels
THE 60-INCH, SIX-BAR SUPERSWEEP™ PICKUP USES
- Six tine bars, single cam
- 144 curved steel tines spaced 2.6 inches apart
- Articulated tine windguard
- Single adjustable-height pickup gauge wheels

TIRE CHOICES

Flotation tires take the bumps out of baling in rough fields to improve ride quality while reducing soil compaction. Choose, from right to left, 1. high flotation (21.5L x 16.1, 10PR), 2. low-profile flotation (18L x 16.1SL, 10PR) or 3. implement tires (31 x 13.5-15, 10PR).